Sit Automation: Inverter Delta VFD-CP2000. View and Download Delta 2000 instruction manual online. Step Pulley Drilling Machine 2:1 Speed Reduction Model; 3:1 Speed Reduction Model. 2000 Drill pdf manual download. View & download of more than 1993 Delta PDF user manuals. Delta; Delta manuals. Instruction Manual: 50-2000. Datasheet VFD-CP2000 DELTA ELECTRONICS, INC. 3 of 21 Delta reserves the right to make ALL RIGHTS RESERVED changes without prior notice 400V 22 ~ 37kW with built-in.

• POWER AMPLIFIER Owner’s Manual POWER TEMP PROTECTION POWER Keep This Manual For Future Reference. POWER AMPLIFIER CLIP LEVEL –dB. • N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

* This applies only to products distributed by YAMAHA KEMBLE MUSIC (U.K.) LTD. • Important Information Please read the following before using the CP2000 Warnings • Do not allow water to enter this unit or allow the unit to become wet.

Fire or electrical shock may result. • Connect this unit’s power cord only to an AC outlet of the type stated in this Owner’s Manual or as marked on the unit. Crack Bdp Software Hosteleria.

• Bridge Mode Hookup.6 3 Using the CP2000.7 Installation. • • 650 W+650 W into 4 stereo, 450 W+450 W into 8 stereo. • 2,000 W into 4 bridged, 1,300 W into 8 bridged. • Yamaha Speaker Processing matches the CP2000 to the Yamaha S115 and S112 loud- speakers. • Three operating modes are provided: STEREO mode in which Channel L and Channel.

• 11 for more information. TEMP indicator This indicator lights up if the temperature of the CP2000’s heatsinks exceed 85 degrees Celsius. Note that this indicator only serves as a warning. It does not indicate operation of the protection system. • SPEAKERS connectors The outputs for each CP2000 channel comprise of one 1/4' phone jack and one pair of 5-way binding posts. The 1/4' phone jacks accept 1/4' phone plugs, while the 5-way binding posts offer several methods of connection, including single or double banana plugs, spade lugs, or bare wires. • Chapter 2—Hookup Examples GND terminal For safety reasons it’s important that the CP2000 is grounded.

The attached power cord has a three-pin plug, and if the ground terminal of the AC outlet to which it is con- nected is grounded, then the CP2000 will be grounded adequately via the power cord. • Channel L inputs. This mode is typically used with a mono source and allows independent volume control of two sets of speakers. Javascript Quiz Game Script there. The following hookup example shows how the CP2000 can be used in PARALLEL mode. • In BRIDGE mode, the L and R channels are combined to form a massive 2000 watt sin- gle-channel amplifier.

The input signal is sourced from the Channel L inputs. The fol- lowing hookup example shows how the CP2000 can be used in BRIDGE mode. • For correct operation, it’s important that the air flow at the front and rear of the CP2000 is not blocked or restricted in any way. If the CP2000 is mounted in a portable rack with removable front and rear covers, be sure to remove the covers before using the CP2000. • To connect an unbalanced source to an INPUT XLR, connect pin 3 (cold) to pin 1 (ground), as shown below. The following table shows which inputs, LEVEL controls, and signal and CLIP indica- tors are active in each CP2000 mode. Channel CP2000—Owner’s Manual Item.

• Connecting Speakers Warning: Turn off all equipment before making any connections. The outputs for each CP2000 channel comprise of one 1/4' phone jack and one pair of 5-way binding posts. The 1/4' phone jacks accept 1/4' phone plugs, while the 5-way binding posts offer several methods of connection, including single or double banana plugs, spade lugs, or bare wire. • Chapter 3—Using the CP2000 The following table shows which outputs can be used in each CP2000 mode and the minimum speaker impedance. Note that this is the total speaker impedance that can be connected to each channel.